Buy All in One Clamp U-99 99-Inch Ultra Wide Grip Clamp with Double T-TrackAll in One Clamp U-99 99-Inch Ultra Wide Grip Clamp with Double T-Track Product Description:
- No more C-clamping with a self-clamping straight edge to guide your power tools for truly straight cuts
- Aluminum extrusion is extra wide for rigidity over the 99 inch length
- Raised T-tracks accept A, Twin, and Ultra series Saw Plate, Router Plate and Stop Block but will not work with Contractor series accessories
- Nylon jaws hold work piece securely and are pre-drilled for accessory Wide Jaws and Tall Jaws
- Distance of 99 inches between jaws allows lengthwise cuts on 4 foot by 8 foot stock
Customer Reviews
Most helpful customer reviews
101 of 102 people found the following review helpful.
Finally, straight cuts with a circular saw
By G. Chastain
I can not begin to describe how well this clamping tool guide works. It is easily adjustable to clamp on any width work piece but, obviously, this one was made to rip 8' sheet material. The guide has three levels of clamping force but the first level is enough to secure the guide so that it will not move during ripping.This guide absolutely does not bow to the side as you rip. You can press the base plate of your circular saw tight against the side of this guide and rip away. For the first time I can rip a full 8' sheet of plywood and the cut is consistent width the full length. This is virtually impossible to do with cheaper guides like the thin-gauge, two-piece one from Johnson.This guide has two t-slot tracks as well so you can design jigs and stops to attach to the guide. I purchased the optional 9"x12" HDPE saw plate for circular saws that runs in the T-track of the guide but I haven't used it yet. I don't know if I will ever have the need to. If the guide doesn't bow sideways, and believe me, this one doesn't, you can get a straight cut without the need of linking your circular saw to the guide with the optional plate.The guide has slots that allow you to insert optional ruled scales (SAE or metric). However, I have purchased these and they are no good. The measuring scale is made of thin plastic laminated on paper and is off by 1/8" within 48". See my review for the "All in One Clamp I-99 99-Inch Scale (English)" product. This applies to all the E. Emerson all in one measurement scales that I have purchased. However, the extra wide surface between the T-slots on the Ultra Wide clamp leaves plenty of room to add a quality adhesive backed measurement tape such as those sold for table saw rip fence rails. I plan to purchase one of those to enhance my Ultra Wide.This clamping tool guide is well worth the price and I'm glad I finally made myself try it. Do yourself a favor, through that cheap two-piece tool guide away, or that not quite straight piece of scrap lumber and buy one of these. You'll be glad you did when you start getting really straight cuts from your circular saw.I also have the 54" Ultra Wide, the 50" standard width and the 36" standard width. See my reviews for those too.
23 of 23 people found the following review helpful.A Ripping Great Straight Edge!
By The Garage
You could buy a straight piece of aluminum angle at any metal supplier and get a straight cut. What really makes the difference with the U99 is the clamping mechanism. The jaws at each end have an agressive grip that doesn't budge, and there's no slack to mess up your careful layout. I have a couple of shorter clamps (not Emersons) and they have a little play in one end or the other. With the U99 I've found that a spring clamp is needed at one end for set up just because it's so long. I spring clamp the free end on the mark then line up the other end and lock the Ultra All-in-one in place.Can you make something that works as well? You probably can, but I prefer to spend my time making things rather than making jigs. Also the shop made circular saw fences I've seen only work with one saw, I have three. The U99 is ready to use right out of the 9 foot long box.
22 of 22 people found the following review helpful.Great tool, simple to use and durable
By Electric Z
I now have three of these clamps. This one got broken by the carrier in shipping. I figure it got slammed on the end pretty hard as these are pretty tough. The blue ends are made of reinforced plastic and while durable with the right amount of force can be broken.Nonetheless, I called the company and they shipped out FedEx the replacement part. They spent enough time on the phone so they were sure I knew how to disassemble and put back together. Pretty easy actually. Now thats customer service and support.I sometimes use two of these together side by side when routing out dado's. They adjust easily and solidly clamp to most any size wood or table. I bought this to cut down a 4 X 8 sheet of plywood to manageable size and also to clamp onto my work bench when the need arises. This is solid enough you learn to rely on using the clamp when working on projects.There is no bend and you cannot find a better straight edge on the market.I just added the wide jaws and would recommend those as well. It just adds a little extra.Highly recommend the product and the company too!
Latest Price: See on Amazon.com!
More Info: See on Amazon.com!
See Customers Review: See on Amazon.com!
